Search
Related topics are listed below.
Camera setup: Flir Blackfly GigE
Modulo Player Remote » Outputs tab » Auto-calibration » Camera setup: Flir Blackfly GigE
Instructions 1. Install the camera driver: Spinnaker SDK p(banner tip).Note : The driver must be installed on both the Modulo Player server and Modulo Player Remote computer. Make sure your camera is connected to the same network as your Remote or Designer and…
Camera setup: Lucid Triton GigE 200S
Modulo Player Remote » Outputs tab » Auto-calibration » Camera setup: Lucid Triton GigE 200S
Instructions 1. Install the camera driver: Arena SDK p(banner tip).Note : The driver must be installed on both the Modulo Player server and Modulo Player Remote computer. Follow one of the two methods below to set your camera’s IP address. Configure IP with…
Server setup
Tutorials – English » Training tutorials » Live Event » Live event : Starting the project » Server setup
If you are working in demo mode on a laptop, we will use the second screen to display the monitoring, which we will configure to display all our outputs. If you have access to a real Modulo Player server, you can use its 4 outputs to fully simulate the live event.…
Network setup
Starter guide » Modulo Player media server » Network setup
You need to check that you are on the same network as your Modulo Player media server. When you received your Modulo Player unit, the box included a sheet with the IP address of your media server. If you do not know how to setup an IP: Go on this page for a PC Go…
Prepare the scene, projectors and camera
Tutorials – English » Training tutorials » Autocalibration of 5 video-projectors on a dome » Prepare the scene, projectors and camera
Scene setup Set the projectors and camera as follow: Video projectors need to cover the entire dome, and have enough overlap between each other to get a seamless projection The calibration camera needs to be as aligned as possible with the top-middle of the…
Setup of EDID and Eyefinity
Tutorials – English » Training tutorials » Live Event » Project transfer on the Media Server » Setup of EDID and Eyefinity
Let’s force the 4 outputs with an EDID and do eyefinity to have an desktop extended over 4 screens. Check that the outputs are correctly configured in the output tab (if you have done the initial setup on a single screen, the resolution of the outputs has been…
Setup and copy of the project
Tutorials – English » Training tutorials » Live Event » Project transfer on the Media Server » Setup and copy of the project
Transfer exercise: The Modulo Player PRO-4 is installed and connected to 2 VPs (e. g. wall projection) + 2 HD LCD screens + 2 LIVE SDI sources (blackmagic player?) + 2 HDMI LIVE sources. Now transfer the show to the server. Connect the hard disk with the whole show to…
Setup the IP address of your PC
How-To » Setup the IP address of your PC
Open the control panel (for example enter control panel on the loop field on the left back of your Windows. Choose network and internet Click on network and sharing center Click on the left on change adapter settings Then choose your network adapter…
Setup the IP address of your MAC
How-To » Setup the IP address of your MAC
First open the control panel. Go on the top menu and choose System preferences. Then choose Network. Choose your adapter and select manually Configure IPV4 to force a manual IP address. Choose an free IP in your network that is on the same network as your Modulo…
Basic setup and start of Modulo Player Lite
Starter guide » Modulo Player Lite » Basic setup and start of Modulo Player Lite
Your Modulo Pi key is activated, your Modulo Player Lite and Modulo Player Remote are installed. Now, it’s time to play! Firewall and antivirus: First, check that your antivirus will not prevent the applications to launch or to communicate. Usually, an…
Préparer la scène, les projecteurs et la caméra
Tutoriels – Français » Tutoriels de formation » Autocalibration de 5 video projecteurs sur un dome » Préparer la scène, les projecteurs et la caméra
Préparer la scène Disposez les video projecteurs et la caméra comme suit : Les vidéo-projecteurs doivent projeter à eux tous sur tout le dôme et avoir suffisamment de recouvrement entre eux La caméra de calibration doit être placée au milieu de la base du…
Auto-calibration
Modulo Player Remote » Outputs tab » Auto-calibration
The objective of autocalibration is to easily obtain one seamless display with multiple video projectors as presented in the image below: Result of an autocalibration with 5 projectors on a dome. Autocalibration can be used with the following screen setups: flat,…
Multi-projector auto-calibration
Multi-projector auto-calibration
Description Achieve a perfectly warped and blended projection in minutes with Modulo Pi’s autocalibration solution. Available as an option for the Modulo Player and Modulo Kinetic series of media servers, the autocalibration feature is designed to automatically…
Autocalibration of 5 video-projectors on a dome
Tutorials – English » Training tutorials » Autocalibration of 5 video-projectors on a dome
Modulo Pi has an autocalibration solution fully integrated into its media servers. The autocalibration solution can be used when projecting on: - Flat surfaces - Curved surfaces - Dome surfaces In this exercice, we will see how to perform an automatic calibration…
Prepare Modulo Player for the calibration
Tutorials – English » Training tutorials » Autocalibration of 5 video-projectors on a dome » Prepare Modulo Player for the calibration
!Before continuing, take care that the software controlling the camera is closed, otherwise Modulo Player will not be able to communicate with the camera. In this chapter we will prepare Modulo Player for the calibration. Important License information *Info: The…
Autocalibration de 5 video projecteurs sur un dome
Tutoriels – Français » Tutoriels de formation » Autocalibration de 5 video projecteurs sur un dome
Modulo Pi intégrère un système d’autocalibration dans ses media serveurs. Ce système d’autocalibration peut être utilisé sur des : - Surfaces planes - Surfaces incurvées - Domes Dans cette exercice, nous allons voir comment réaliser une…
Perform the autocalibration
Tutorials – English » Training tutorials » Autocalibration of 5 video-projectors on a dome » Perform the autocalibration
*Before moving forward, we remind you that all lights – natural or artificial – need to be turned off or hidden. Indeed, any reflection in the room can mar the autocalibration operation. On the Output page click on Autocalib. The autocalibration…
Panasonic PTZ AW-Hexxx
Modulo Player Remote » Devices tab » PTZ » Panasonic PTZ AW-Hexxx
Choose this device when you want to control Panasonic PTZ AW-Hexxx with Modulo Player. Settings: Name: User-friendly name Ip: Enter the IP address of the camera Task action: Power On/Off Save Preset (Index) Recall Preset (index) Set Preset Recall Speed (value) Stop…
NDI PTZ
Modulo Player Remote » Devices tab » PTZ » NDI PTZ
Choose this device to control a PTZ camera with the NDI protocol. Settings: Name: User-friendly name Source: Choose the NDI PTZ source in the list. If you don’t see it, click on the refresh button. A user interface allows you to direclty control your PTZ from…
NDI source
Modulo Player Remote » Media tab » NDI source
You can now add a NDI source. This allows you to stream sources using the NewTek protocol over IP. Modulo Player detects automatically all NDI sources in the same network. You can download serveral NDI applications. For more information please visit official NDI…
Réaliser l’autocalibration
Tutoriels – Français » Tutoriels de formation » Autocalibration de 5 video projecteurs sur un dome » Réaliser l’autocalibration
*Avant de continuer, assurez-vous d’avoir caché ou éteind toute lumière qui pourrait parasiter la calibration. Éviter également toute réflexion de lumière dans la pièce. Depuis le Menu, open V-Nodes > Autocalibration. L’autocalibration est en…
Multi-projector auto-calibration for a dome
Application notes » Multi-projector auto-calibration for a dome
Multi-projector auto-calibration in dome configuration Set-up relies on: 1 x Modulo Player Pro with 6 outputs 1 x dongle with Auto-Calibration option for 6 outputs 1 x PoE camera (not-included) Powerful Auto-Calibration module: Multi-projector automatic edge blending…
Refaire une autocalibration existante
Tutoriels – Français » Tutoriels de formation » Autocalibration de 5 video projecteurs sur un dome » Refaire une autocalibration existante
Si vous devez refaire une calibration sur un système de video projecteurs déjà calibrés, vous avez la possibilité de reprendre une autocalibration afin de la réaliser à nouveau avec les mêmes réglages qu’auparavant. Pour cela: Allumer tous les video…
Retake the autocalibration on an existing installation
Tutorials – English » Training tutorials » Autocalibration of 5 video-projectors on a dome » Retake the autocalibration on an existing installation
If you have a system of projectors and servers in place, like in a permanent installation, you may want to retake the actual autocalibration. For instance, after a video projector is replaced, you simply need to operate the autocalibration with the same parameters you…
Soft edge blending and live mixer
Application notes » Soft edge blending and live mixer
Soft edge blending and live mixer configuration Set-up relies on: 1 x Modulo Player Pro with 4 outputs Live capture cards (option): - 3 × 3G-SDI - 2 x HDMI 2.0 Versatile display capabilities: Multi-projector soft edge blending Powerful image & video…
X-Maps warping
Tutorials – English » Training tutorials » Architectural video mapping » X-Maps warping
First, import the Photoshop PSD file. Then go to the Media tab and click on the “refresh” button to load the media previously copied into the show. Then, go to the Playlist tab. Add cues, leave the cue 1 empty. Load the test Pattern into cue 2 You can…
Soft edge blending, mapping, and live mixer
Application notes » Soft edge blending, mapping, and live mixer
Soft edge blending, projection mapping, and live mixer configuration Set-up relies on: 1 x Modulo Player Pro with 6 outputs Live capture cards (option): - 1 × 12G-SDI or 4 × 3G-SDI - 2 x HDMI 2.0 Versatile display capabilities: Multi-projector soft edge…
Top menu
Modulo Player Remote » Top menu
You can click on the menu on the top right of the remote to have access to the following actions: Setup the MIDI controller on your Remote Setup the StreamDeck on your Remote Open the online manual (more friendly help than offline) Open the offline manual when…
Properties
Modulo Player Remote » Playlist tab » Layer settings » Properties
From here you can setup the geometry of your media: • Position: Enter the position of your media • Anchor mode: Choose the anchor mode: Type the start position in pixels, or configure it in relation to the pixel Worskpace. Center the center of the media on…
Rotary IP
Modulo Player Remote » Devices tab » Tracking » Rotary IP
Choose this device to mesure an angular rotation or a distance if this device is associated with Draw Wire. Settings: Name: User-friendly name IP: Enter the ip address of your device. Your device and Modulo Player need to be in the same subnet Port: TCP/IP port. 6000…
Master-Slave Copy
Modulo Player Remote » Playlist tab » Master-Slave Copy
When you have several Modulo Player in your network, one in Master, the others in Slave mode in the same cluster, you can copy one playlist from your master computer to all slave Modulo Players. This will replicate the playlist on all slave Modulo Players. This helps…
Visca PTZ
Modulo Player Remote » Devices tab » PTZ » Visca PTZ
Choose this device when you want to control a PTZ using the VISCA protocol. Settings: Name: User-friendly name Serial / IP: Choose mode Settings for serial mode: Port: Choose the serial number port Baudrate: Choose the matching baudrate Settings for IP mode: IP:…
General
Modulo Player Remote » Control » General
This tab is for general settings. Project folder: Remotely select the project folder on your media server. The project folder is always created and hosted in the Data hard drive of the media server (D:), never in the remote. The D: drive contains all media files,…
Optimize the calibration with the parameters
Tutorials – English » Training tutorials » Autocalibration of 5 video-projectors on a dome » Optimize the calibration with the parameters
After the calibration, we might observe that one or several projectors’ pictures are not perfectly adjusted with the others. First, check that there was no undesirable lights and nothing moving in front of the camera while you were performing the…
Live Event
Tutorials – English » Training tutorials » Live Event
In this third exercise, we will learn how to setup a show typical of live events involving multiple projectors and screens. This show will simulate a corporate event announcing the launch of a new car. Here is a 3D preview of the final setup. It will involve the…
Modulo Wing
Companion Apps » Modulo Wing
Modulo Wing: Modulo Wing is a free application to access all your playlists and tasks on Android devices, iPad, Mac or PC. Thanks to this overview, playlists and tasks come all available anytime over wifi for show control, monitoring… Download: For…
Devices tab
Modulo Player Remote » Devices tab
This tab allow you to add devices and do the setup. Click on the + to add a new device.
Wizard
Modulo Player Remote » Outputs tab » Wizard
This Wizard allows you to quickly create outputs when you have a basic setup. Click on the Wizard button to open the dialog box. First adjust the pixel workspace in the general tab. Enter the following informations: • Width and height (Edid resolution) for each…
Media tab
Modulo Player Remote » Media tab
The Media tab lists all media available on the project folder and subfolders. NB: Refer to the Media Creation page for codec and format specifications. Media can be either in sub-folders or in the base folder of your project. The non-compressed server versions…
Transition
Modulo Player Remote » Playlist tab » Layer settings » Transition
In this tab, you can apply basic transitions for live media. For more complex setup, we advise you to use the new Live Mixer user interface instead. • Choose from a list of transition effects: - Last State: Transition from one point to the other starting from…
UI Designer tab
Modulo Player Remote » UI Designer tab
The User Interface (UI) Designer is a graphic Designer Interface where you can create your own customized interfaces. You can create your own pages to control a show from a computer, a tablet or an iPad, or another touch device. You can add as many UI as you want,…
Analog Way LiveCore
Modulo Player Remote » Devices tab » Switchers » Analog Way LiveCore
Choose this device to control Analog Way LiveCore series. Settings: Name: User-friendly name IP: Enter the ip address of your switcher. Your device and Modulo Player need to be in the same subnet MAC: Enter the Mac address of your switcher to use commande Wake…
Paramétrage EDID et Eyefinity
Tutoriels – Français » Tutoriels de formation » Live Event » Portage du projet sur le média serveur » Paramétrage EDID et Eyefinity
On va maintenant forcer les 4 sorties avec une EDID et on fait le Eyefinity pour avoir un bureau étendu sur 4 écrans. On vérifie que les outputs sont correctement configurées dans l’onglet Output. Si on a fait le setup initial sur un seul écran, la…
Sanyo
Modulo Player Remote » Devices tab » Video Projectors » Sanyo
Choose this device to control your Sanyo video-projectors. Settings: Name: User-friendly name Serial/IP : Choose serial or IP IP: Enter the ip address of your video projector. Your device and Modulo Player need to be in the same subnet Port: TCP/IP port. 1000 is…
Modulo Shortcut
Companion Apps » Modulo Shortcut
Modulo Shortcut: Use this free application to easily take control of your Keynote or PowerPoint presentations using common shortcuts. Download: For Windows PowerPoint: Connect to the Customer Area > Modulo Player > Companion Apps section Then install Modulo…
Serial
Modulo Player Remote » Devices tab » Low Level » Serial
Choose this device to control a device on a serial port. Optionally, you will need a USB to RS232 converter to connect. Settings: Name: User-friendly name Port: Select the serial port. Go to the device manager to find the good one Baudrate: Select a value in the…
Monitoring tab
Modulo Player Remote » Monitoring tab
The Monitoring tab is where you can setup a confidence screen to monitor live inputs, outputs and Program in a mosaic view. You can use one of the media server physical outputs to display the monitoring, or you can stream your confidence screen in NDI. If you…
Audio
Modulo Player Remote » Control » Audio
You can choose the renderer mode and the soundcard to playback sound. MME: You can set up the audio rendering engine. By default, Modulo Player uses the Windows audio mixer (MME) to play 44.1kHz or 48kHz stereo audio files (up to 7.1 depending on your sound…
Deltacast
Modulo Player Remote » Control » Deltacast
This panel lists the available Deltacast live capture cards when they are properly installed on your system. You can check that your cards are properly installed and in the correct order and type. To ensure good performance, check that the value for PCIe and Field…
Deltacast
Hardware » Driver update » Deltacast
To check that you have the good drivers: Go on tab Control, click on “settings”, go to Deltacast tab: This panel lists the available Deltacast live capture cards when they are properly installed on your system. You can validate that your cards are…
Notifications
Modulo Player Remote » Control » Notifications
You can setup the email notifications in this panel. You need to create an email account that you will use to send emails to. SMTP server: Enter the SMTP server address provided by your email provider. Choose the correct port and the encryption method following…
TCP Server
Modulo Player Remote » Devices tab » Low Level » TCP Server
Choose this device to create a TCP/IP server. other device can connect to this server. Settings: Name: User-friendly name Port: The TCP/IP port binded Task action: Command: You can add a carriage return using the string \r (0×0D in hexadecimal format). You…
UDP
Modulo Player Remote » Devices tab » Low Level » UDP
Choose this device to send and receive UDP packet to/from other devices. Settings: Name: User-friendly name IP: Enter the ip address your device. Your device and Modulo Player need to be in the same subnet Port: UDP port Task action: Command: You have to enter…
Kinesys
Modulo Player Remote » Devices tab » Tracking » Kinesys
Choose this device to receive motion information from the Kinesys K2 solution. Settings: Name: User-friendly name Multicast: Choose Multicast mode or unicast (multicast is the default value) IP: Enter the ip address of the multicast network (default value is…
Modulo Panel
Companion Apps » Modulo Panel
Modulo Panel: Once you have created your custom panels in the UI Designer, Modulo Panel allows to easily access and use the interfaces directly from a Mac, PC, as well as Android and iOS devices. Assign different panels depending on your needs (show control,…
Pjlink
Modulo Player Remote » Devices tab » Video Projectors » Pjlink
This device allows you to control Panasonic video-projectors and many other brands that support this protocol. Settings: Name: User-friendly name IP: Enter the ip address of your video projector. Your device and Modulo Player need to be in the same subnet Port:…
TCP Client
Modulo Player Remote » Devices tab » Low Level » TCP Client
Choose this device to control a device sending TCP/IP command. Settings: Name: User-friendly name IP: Enter the ip address of your device. Your device and Modulo Player need to be in the same subnet Port: Choose the correct TCP/IP port Task action: Command: You…
Digimap-MIDI
Tutorials – English » Training tutorials » Workshop » Digimap-MIDI
We will now use a MIDI controller to interact with the content using digimap. The MIDI controller is connected to the server. For example, you can use NanoKontrol2 from Korg. We go to the MIDI controller setup and activate the input and choose NANOKONTROL2. you move a…
Modulo Sync
Companion Apps » Modulo Sync
Modulo Sync: Modulo Sync is a file synchronization tool for Modulo Player. Use this free application to transfer media in several servers at the same time, or to get a backup of your project (excluding media files). Download: For PC (Windows x32): Connect to the…
Digimap – MIDI
Tutoriels – Français » Tutoriels de formation » Workshop » Digimap – MIDI
Nous allons maintenant utiliser un contrôleur MIDI pour interagir avec le contenu en utilisant le Digimap. On branche le contrôleur MIDI sur le serveur. On peut par exemple utiliser NanoKontrol2 de Korg. On va dans le setup du contrôleur MIDI et on active…
Timecode
Tutorials – English » Training tutorials » Workshop » Timecode
This workshop will allow you to synchronize a playlist on timecode. Timecode: Timecode is used to synchronize several techniques (e.g. video server media, sound player and lighting console together) in a show. In general, one device is the master (it generates the…
Software overview
Introduction » Software overview
Intuitive software Modulo Player works with a dedicated Modulo Player Remote, a control software designed to optimize setup, workflow management, and show control. No matter the number of media servers, one Modulo Player Remote is used to work on the server(s)…
Add background
Tutorials – English » Training tutorials » Projection mapping » Add background
We will now project another media on the background behind the cube using the same projector. Open the General tab and increase the Pixel Workspace from 1920×1080 to 3840×1080. Open the Output tab and select the Main map above X-MAP1. Then add another…
DMX
Modulo Player Remote » Devices tab » Control » DMX
This device allows you to receive or send DMX via Art-Net protocol. Settings: Name: User-friendly name Input Enable: Enable or disable Input Input universe and subnet: Choose the input universe and subnet Output Enable: Enable or disable output Output universe and…
X-Map
Modulo Player Remote » Outputs tab » X-Map
For the most complex shapes, our exclusive X-Map function will help you save time and money. Most of the mappings on our Showcase gallery are done using this smart and user-friendly feature. When having different levels of depth on your projection surface or a…
Préparer Modulo Player pour la calibration
Tutoriels – Français » Tutoriels de formation » Autocalibration de 5 video projecteurs sur un dome » Préparer Modulo Player pour la calibration
!Avant de poursuivre, assurez-vous que le logiciel contrôlant la caméra est fermé, sinon Modulo Player ne pourra pas communiquer correctement avec la caméra. Dans ce chapitre nous allons préparer le logiciel Modulo Player pour la calibration. Important :…
General tab
Modulo Player Remote » General tab
This tab is accessible only if the media server application is currently running (green icon). The General tab is divided in 3 parts: Top menu, information, and media server’s global settings. Top Menu: The top menu allows you to Create, Load, Save, Save As,…
Timecode
Tutoriels – Français » Tutoriels de formation » Workshop » Timecode
Cet atelier va vous permettre de synchroniser une playlist sur du timecode. Timecode : On utilise du timecode pour synchroniser plusieurs techniques entre elles dans un spectacle, par exemple média serveur vidéo, player son et console lumière. En général, un…
Playlist Overview
Modulo Player Remote » Playlist tab » Playlist Overview
Global Overview: At the top of the page, underneath the general menu bar, choose the playlist you want to edit (tabs) (cf ). You can create a new playlist clicking on the button (cf ) . If you want to delete a playlist, shuffle playlists order, or rename a…
TCP/IP external control protocol
TCP/IP external control protocol
This protocol allows you to control the Modulo Player application with a TCP/IP client connected to the Modulo Player application. We use this convention to separate each command : At the end of each command, you need to add a separator: ‘\n’ in ascii (or…
Digimap tab
Modulo Player Remote » Digimap tab
The Digimap tab allows you to take control of some playlist parameters from a sensor or an external device. This way, you can add interactivity to your show. For instance, you can move a panel on a stage (with the projection moving along with it). You can…